• EI
  • Scopus
  • 食品科学与工程领域高质量科技期刊分级目录第一方阵T1
  • DOAJ
  • EBSCO
  • 北大核心期刊
  • 中国核心学术期刊RCCSE
  • JST China
  • FSTA
  • 中国精品科技期刊
  • 中国农业核心期刊
  • CA
  • WJCI
  • 中国科技核心期刊CSTPCD
  • 中国生物医学SinoMed
中国精品科技期刊2020
向晨曦,李钰金,高瑞昌,等. 打印参数对未漂洗鲟鱼糜凝胶3D打印成型效果的影响[J]. 食品工业科技,2022,43(2):1−8. doi: 10.13386/j.issn1002-0306.2021040100.
引用本文: 向晨曦,李钰金,高瑞昌,等. 打印参数对未漂洗鲟鱼糜凝胶3D打印成型效果的影响[J]. 食品工业科技,2022,43(2):1−8. doi: 10.13386/j.issn1002-0306.2021040100.
XIANG Chenxi, LI Yujin, GAO Ruichang, et al. Effect of Printing Parameters on the 3D Printing Molding Effect of Unrinsed Sturgeon Surimi Gel[J]. Science and Technology of Food Industry, 2022, 43(2): 1−8. (in Chinese with English abstract). doi: 10.13386/j.issn1002-0306.2021040100.
Citation: XIANG Chenxi, LI Yujin, GAO Ruichang, et al. Effect of Printing Parameters on the 3D Printing Molding Effect of Unrinsed Sturgeon Surimi Gel[J]. Science and Technology of Food Industry, 2022, 43(2): 1−8. (in Chinese with English abstract). doi: 10.13386/j.issn1002-0306.2021040100.

打印参数对未漂洗鲟鱼糜凝胶3D打印成型效果的影响

Effect of Printing Parameters on the 3D Printing Molding Effect of Unrinsed Sturgeon Surimi Gel

  • 摘要: 为进一步提高未漂洗鲟鱼糜凝胶的打印质量,本文探究了打印速度、分层高度、填充密度、喷嘴直径、挤出程度和温度等相关打印参数对鱼糜凝胶3D打印成型效果的影响,并进行了打印精度评价。结果表明,分层高度要与喷嘴直径相同或略低于喷嘴直径,分层高度、喷嘴直径和打印速度越大,打印效率越高。综合打印效果和打印效率可确定最佳打印参数为喷嘴直径1.20 mm、分层高度1.2 mm、填充密度100%、挤出程度100%、打印速度25 mm/s和温度25 °C。在此打印参数下,打印鱼糜结构紧密,成型性好,打印精度高,可获得高质量的3D打印鱼糜。

     

    Abstract: In order to further improve the printing quality of unwashed sturgeon surimi gel, this paper explored the influence of printing parameters such as printing speed, layering height, filling density, nozzle diameter, extrusion degree and temperature on the 3D printing effect of surimi gel, and evaluated the printing accuracy. The results showed that the layering height should be the same as or slightly lower than the nozzle diameter, and the higher the layering height, nozzle diameter and printing speed were, the higher the printing efficiency was. Based on the comprehensive printing effect and printing efficiency, the optimal printing parameters were determined as nozzle diameter 1.20 mm, layering height 1.2 mm, filling density 100%, extrusion degree 100%, printing speed 25 mm/s and temperature 25 °C. Under these printing parameters, the structure of the printed surimi was tight, and the formability was good and the printing accuracy was high, which could obtain high-quality 3D printing surimi.

     

/

返回文章
返回