Optimization of Molding Process of Daqu’s Multi Position Press

GAO Jian; TIAN Jianping; WANG Kaizhu; HUANG Danping; LUO Huibo; HUANG Dan; WU Xiangdong

doi:10.13386/j.issn1002-0306.2021070051

Volume 43 Issue 8

Apr. 2022

Turn off MathJax

Article Contents

Abstract

References

Science and Technology of Food Industry > 2022 > 43(8): 172-179. > DOI: 10.13386/j.issn1002-0306.2021070051

GAO Jian, TIAN Jianping, WANG Kaizhu, et al. Optimization of Molding Process of Daqu’s Multi Position Press[J]. Science and Technology of Food Industry, 2022, 43(8): 172−179. (in Chinese with English abstract). doi: 10.13386/j.issn1002-0306.2021070051.

Citation:

PDF (9009 KB)

Optimization of Molding Process of Daqu’s Multi Position Press

1.
College of Mechanical Engineering, Sichuan University of Science & Engineering, Yibin 644005, China
2.
Liquor Marking Biological Technology and Application of Key Laboratory of Sichuan Province, Yibin 644005, China

More Information

Received Date: July 05, 2021
Available Online: February 13, 2022

Graphical Abstract

Abstract

Abstract

Daqu is a saccharifying agent, starter culture agent and aroma generating agent in the process of liquor brewing. The quality of Daqu directly affects the quality of liquor. In order to find the Daqu’s optimal molding process parameters during the pressing process of Daqu’s multi position press, this paper deployed area ratio of surface pulping and the uniform factor of internal moisture content of Daqu as evaluation indexes. Surface response experiment studied the influence of three factors of different pressing speed, stepping times and forming times on Daqu^,s pulp extraction effect and moisture content uniformity. The research results showed that the impact of each process parameter on the pulping effect of Daqu ranked as follows: Stepping times>forming times>pressing speed. The influence on the uniformity of Daqu water content was pressing speed>stamping times>forming times. The best process parameters were: Pressing speed (A)=20 mm/s, times of trampling (B)=20, and times of molding (C)=7. Under the conditions of the process parameters, the Daqu obtained by pressing Daqu showed that the effective area ratio of pulping was 85.66%, and the uniformity factor of water content inside Daqu was 6.37. The thesis provided productive and practical technical support for the standardization and industrialization of liquor Daqu pressing production.
- Daqu molding,
- process parameters,
- pulping effect,
- moisture content

FullText(HTML)

References (35)

References

[1]	刘绪兴, 程鹏, 陈才, 等. 真菌在大曲酒生产中的应用研究[J]. 酿酒科技,2020(7):50−57. [LIU X X, CHENG P, CHEN C, et al. Application of fungi in Daqu Baijiu production[J]. Liquor-Making Science & Techonologe,2020(7):50−57.
[2]	钱冲, 廖永红, 张弦, 等. 白酒生产机械自动化技术应用进展[J]. 中国酿造,2013,12(32):5−8. [QIAN C, LIAO Y H, ZHANG X, et al. Application progress of mechanical automation liquor-production technologies[J]. China Brewing,2013,12(32):5−8.
[3]	HE G Q, HUAN J, WU C D, et al. Bioturbation effect of fortified Daqu on microbial community and flavor metabolite in Chinese strong-flavor liquor brewing microecosystem[J]. Food Research International, 2020: 9.
[4]	顾强, 田建平, 杨海栗, 等. 多工位柔性压曲机锤头设计与压曲过程仿真分析[J]. 食品工业,2018,39(7):246−250. [GU Q, TIAN J P, YANG H L, et al. Multi-station flexible bending press hammer design and simulation analysis of buckling process[J]. The Food Industry,2018,39(7):246−250.
[5]	王永亮, 张治刚, 李二召, 等. 贾湖酒业自动化制曲生产线的探讨[J]. 酿酒, 2019, 5(46): 101–103. WANG Y L, ZHANG Z G, LI E Z, et al. Discussion on automated Koji production line of Jiahu liquor industry[J]. Liquor Making, 2019, 5(46): 101–103.
[6]	钱冲, 廖永红, 张弦, 等. 白酒酿造新技术应用进展[J]. 酿酒科技,2014(7):88−94. [QIAN C, LIAO Y H, ZHANG X, et al. Application progress of new Baijiu(liquor)-making techniques[J]. China Brewing,2014(7):88−94.
[7]	CHEN T Y, JIA H L, ZHANG S W, et al. Optimization of cold pressing process parameters of chopped corn straws for fuel[J]. Energies,2020:21.
[8]	SONG X B, ZHANG S Y, WU Y M, et al. Investigation on the properties of the bio-briquette fuel prepared from hydrothermal pretreated cotton stalk and wood sawdust[J]. Renewable Energy,2020:8.
[9]	胡建军, 雷廷宙, 何晓峰, 等. 小麦秸秆颗粒燃料冷态压缩成型参数试验研究[J]. 太阳能学报,2008(2):241−245. [HU J J, LEI T Z, HE X F, et al. Experimental research on the compressing molding parameter under cold conditions for wheat straw pellet fuel[J]. Acta Energlae Solaris Sinica,2008(2):241−245. doi: 10.3321/j.issn:0254-0096.2008.02.021
[10]	WANG X Y, LI H X, GU J F, et al. Pressure analysis of dynamic injection molding and process parameter optimization for reducing warpage of injection molded products[J]. Polymers,2017,9(12):85. doi: 10.3390/polym9030085
[11]	WANG G Q, WANG Y M, YANG D Y. Study on automotive back door panel injection molding process simulation and process parameter optimization[J]. A. Kumar. Advances in Materials Science and Engineering,2021,2021:1−15.
[12]	LU C R, XU N, ZHENG T, et al. The optimization of process parameters and characterization of high-performance CF/PEEK composites prepared by flexible CF/PEEK plain weave fabrics[J]. Polymers,2018,11(1):53. doi: 10.3390/polym11010053
[13]	赵盼, 史耀耀, 康超, 等. 复合材料机器人纤维铺放工艺参数优化[J]. 西北工业大学学报,2018,36(4):693−700. [ZHAO P, SHI Y Y, KANG C, et al. Optimization of process parameters for robotic fibre placement[J]. Journal of Northwestern Polytechinical University,2018,36(4):693−700. doi: 10.3969/j.issn.1000-2758.2018.04.013
[14]	樊玲玲, 孔孟, 孙大龙. 基于响应面法PE吹塑用汽油瓶工艺参数优化分析[J]. 塑料科技,2021,49(4):66−70. [FAN L L, KONG M, SUN D L. Optimization analysis of process parameters for PE blowing gasoline bottle base on response sureface method[J]. Plastic Science and Technology,2021,49(4):66−70.
[15]	刘斐然, 纵荣荣, 李乐乐, 等. 汽车后风挡横梁冲压工艺仿真分析与优化设计[J]. 河北工业大学学报,2020,49(3):55−62. [LIU F R, ZONG R R, LI L L, et al. Stamping process simulation analysis and optimization design for a car-rear-windshield-cross beam[J]. Journal of Hebei University of Technology,2020,49(3):55−62.
[16]	张明. 机械制曲过程中影响小麦粉碎度的因素探究及调控[J]. 酿酒科技,2019(1):76−80,85. [ZHANG M. Investgation on and control of the factors influencing wheat crushing degress in the process of mechanical Daqu-making[J]. Liquor-Making Science & Techonologe,2019(1):76−80,85.
[17]	黄海飞, 田建平, 王开铸, 等. 曲房环境温湿度场的数值模拟及分布规律[J]. 现代食品科技,2020,36(9):148−155,40. [HUANG H F, TIAN J P, WANG K Z, et al. Numerical simulation and distribution of ambient temperature and humidity field in Qufang[J]. Modern Food Science and Technology,2020,36(9):148−155,40.
[18]	DENG L, MAO X, LIU D, et al. Comparative analysis of physicochemical properties and microbial composition in high-temperature Daqu with different colors[J]. Frontiers in Microbiology,2020,11:588117. doi: 10.3389/fmicb.2020.588117
[19]	叶建秋, 黄丹平, 田建平, 等. 高光谱图像技术检测大曲发酵过程中的水分含量[J]. 食品与发酵工业,2020,46(9):250−254. [YE J Q, HUANG D P, TIAN J P, et al. Detection of water content in Daqu during fermentation using hyperspectral image technology[J]. Food and Fermentation Industries,2020,46(9):250−254.
[20]	HUANG H P, HU X J, TIAN J P, er al. Multigranularity cascade forest algorithm based on hyperspectral imaging to detect moisture content in Daqu[J]. Journal of Food Process Engineering,2021,44(3):13633.
[21]	孙婷, 胡新军, 田建平, 等. 基于高光谱成像技术的大曲酸度值预测及其可视化[J]. 食品与发酵工业,2020,46(17):226−231. [SUN T, HU X J, TIAN J P, et al. Predition and visualization of Daqu acidity based on hyperspectral imaging technology[J]. Food and Fermentation Industries,2020,46(17):226−231.
[22]	张静. 多点采压压曲机设计及其关键结构件仿真研究[D]. 太原: 太原理工大学, 2009. ZHANG J. Research on the design of multi-sports bending press and the simulation research of its’key essential element[D]. Taiyuan: Taiyuan University of Technology, 2009.
[23]	赵凤琦. 我国白酒产业可持续发展研究[D]. 北京: 中国社会科学院研究生院, 2014. ZHAO F Q. Research on sustainable development of Liquor industry in China[D]. Beijing: Graduate School of Chinese Academy of Social Sciences, 2014.
[24]	温翔. 转盘式制曲设备的设计与试验研究[D]. 南昌: 江西农业大学, 2018. WEN X. Design and experimental research of turntable making starter block equipment[D]. Nanchang: Jiangxi Agricultural University, 2018.
[25]	李瑞. 汾酒用曲块制作机理及其关键技术研究[D]. 太原: 太原理工大学, 2011. LI R. Study on mechanism and key technology of fen Chiew starter making [D]. Taiyuan : Taiyuan University of Technology, 2011.
[26]	秦禹. 凸轮分割式旋转压曲机的设计与传动系统的研究[D]. 太原: 太原理工大学, 2015. QIN Y. Design on cam indexers revolving distiller’s yeast press machine and research on it’s drive system [D]. Taiyuan: Taiyuan University of Technology, 2015.
[27]	李大和. 白酒工人培训教程 [M]. 北京: 中国轻工业出版社, 1999: 6 LI D H. Liquor worker training course [M]. Beijing: China Light Industry Press, 1999: 6.
[28]	中华人民共和国工业和信息化部门. QB/T 4257-2011: 酿酒大曲通用分析方法[S]. 北京: 中国轻工业出版社, 2011. Ministry of Industry and Information Technology. QB/T 4257-2011: General analysis method for liquor-making Daqu[S]. Beijing: China Light Industry Press, 2011.
[29]	HUANG H P, HU X J, TIAN J P, et al. Rapid detection of the reducing sugar and amino acid nitrogen contents of Daqu based on hyperspectral imaging[J]. Journal of Food Composition and Analysis,2021,101:103970. doi: 10.1016/j.jfca.2021.103970
[30]	王贤, 丁琳. 中高温大曲制曲过程关键控制点探析[J]. 酿酒科技,2015(3):87−89. [WANG X, DING L. Exploration on the critical control points of medium/higt-temprature Daqu culture[J]. Liquor-Making Science & Techonologe,2015(3):87−89.
[31]	周斐成, 吴生文, 朱庆圣, 等. 特香型大曲发酵过程中曲块不同部位理化指标及主要酶系动态分析[J]. 中国酿造,2019,38(4):58−64. [ZHOU F C, WU S W, ZHU Q S, et al. Physicochemical indexes and dynamic analysis of main enzymes in different layers of Te-flavor Daqu during fermentation process[J]. China Brewing,2019,38(4):58−64.
[32]	毛洪川. 整粒高粱酿造浓香型白酒的工艺开发及应用研究[D]. 绵阳: 西南科技大学, 2017. MAO H C. Development and application of a new technology of Luzhou flavour liquor using intact sorghum as raw material[D]. Mianyang: Southwest University of Science and Technology, 2017.
[33]	唐洁, 陈申习, 林斌, 等. 清香小曲白酒新工艺中微生物及环境因子对酒体风味变化的影响[J]. 食品与发酵工业,2019,45(17):40−47. [TANG J, CHEN S X, LIN B, et al. Effects of microorganisms and environmental factors on changes in aroma composition in Fen-flavor Xiaoqu Baijiu[J]. Food and Fermentation Industries,2019,45(17):40−47.
[34]	潘天全, 程伟, 张杰, 等. 金种子浓香型中高温大曲制曲工艺控制探析[J]. 酿酒,2021,48(3):69−73. [PAN T Q, CHENG W, ZHANG J, et al. Study on Koji-making process control of Jinzhongzi Nonxiang medum and high temperature Daqu[J]. Liquor Making,2021,48(3):69−73. doi: 10.3969/j.issn.1002-8110.2021.03.023
[35]	JEFFREY N R, CHRITOPHER R E, SIMON M C, et al. Model comparison in ANOVA[J]. Psychonomic Bulletin & Review,2016,23(6):1779−1786.

Supplements (0)

Cited By

Cited by

Periodical cited type(5)

1.	赵斌，李娣娣，袁源，韦婷. 发酵型功能酒的现代研究进展. 酿酒. 2025(02): 43-49 .
2.	陈乙源，洪嘉欣，黄河，王硕，武亚帅，赵东瑞，孙金沅，黄明泉，孙啸涛. 基于GC×GC-MS分析不同等级浓香型白酒的关键风味化合物. 中国酿造. 2025(03): 29-35 .
3.	舒翔，邱奇琦. 果酒降酸专利技术分析. 安徽农学通报. 2024(04): 97-101 .
4.	廖娟，李嘉宇，黄杰惠，陈博慧，杨涛. 耐低温酵母的分离鉴定及对低温酿造米酒品质的影响. 食品工业科技. 2024(07): 159-166 . 本站查看
5.	王爱灵，张梅，申娜娜，徐梦文，章骏伟，李瑞龙，兰伟. 黑果腺肋花楸果酒生产工艺研究进展. 滁州学院学报. 2024(02): 21-28 .